Pool Doctor
Robinhood ChainHigh Risk

SPCX/USDG

2 things keep this pool out of Best Practices: 1 you can fix on this pool and 1 that needs a new pool.

Explore a better configuration.

Import this pool into Lab and compare your proposed changes.

Improve this pool ↗

Where it stands, where it can go

  1. Best Practices
    • A new pool built to the recipe
  2. Neutral
  3. High Risk
    Now

Is it tradable right now

Separate from the tier: whether swaps work and routers will find the pool.

  • Price feed: ProblemFeed down

    The provider had no usable price on Metric's last reading, so swaps revert until it does.

  • Trading: OKActive

    The pool is not paused.

  • Liquidity for routing: Check$0.00

    Most aggregators only route to pools holding about $1,000 or more. Below that, expect little or no aggregator flow.

  • Executable depth: ProblemTrading blocked

    Available output: 0 raw SPCX units; 0 raw USDG units. This is a depth snapshot, not a guarantee for any trade size.

  • StopLoss: OK15% drawdown

    Rejects a swap that takes a bin more than 15% below its peak. The peak decays 15% per day. A bin's first trade is exempt.

  • Spread split: CheckLPs 60% / curator 20% / Metric 20%

    The curator share is above the factory's current cap of 15%. It is lowered to the cap the next time Metric updates this pool's protocol fee.

  • Last 24 hours: Info0 swaps, $0.00 volume

    No swaps reached this pool in the last day.

Contracts & extensions
Pool0xEff1…115e
Price Provider0x07ca…55f7

Anchored, immutable parameters, 15s staleness

You can fix these on this pool

Calls the pool admin can make today. No new pool, no one else involved.

StopLoss settings can still change

Fix in place

The admin can loosen or disable the StopLoss after LPs deposit. Any timelock shorter than the maximum only delays that.

Lock the StopLoss by setting its timelock to the uint40 maximum. This is permanent.

View fix instructions (4 steps)
  1. 01
    Check the settings you are about to freeze: drawdown is 15% and decay is 15% per day. Both must be 15% or less, and a drawdown of 0 would freeze the StopLoss switched off.
  2. 02
    Cancel any drawdown, decay or watermark proposal that is still queued. A queued change stays executable after the lock and fails the tier check.
  3. 03
    From the pool admin wallet, call this on 0xE4038fA09f0bB9963068afaF97BE0c045155090D:
    proposeOracleStopLossTimelock(0xEff1B1A268545E024662c3399E26dFbAEBfe115e, 1099511627775)
  4. 04
    Wait out the current timelock (1 hours), then call:
    executeOracleStopLossTimelock(0xEff1B1A268545E024662c3399E26dFbAEBfe115e)
stop_loss_mutableConfigure a pool ↗

These are permanent on this pool

Fixed at creation. The only way past them is a new pool.

Tokenized stock priced without its multiplier

Needs a new pool

The oracle prices one share, not one token. The pool drifts with every dividend and is off by the split ratio after a split.

This pool's provider is fixed forever, so the fix is a new pool.

View fix instructions (3 steps)
  1. 01
    Deploy an Anchored Price Provider that reads this token through the Multiplier Oracle, with immutable parameters.
  2. 02
    Create a new pool that uses it, with the provider fixed.
    priceProviderTimelock = type(uint256).max
  3. 03
    Move liquidity to the new pool once it passes the launch checks.
multiplier_token_unscaledOracles ↗

Recipe for the replacement pool

The settings a new pool needs for Best Practices, next to what this pool has. Rows marked Change are the ones that differ.

SettingThis poolNew pool
Price ProviderAnchored, immutable parameters, no issuer multiplierAnchored, immutable parameters, reading the Multiplier OracleChange
Feed staleness bound15 s15 s or lessKeep
Provider replacementFixedFixed: priceProviderTimelock = type(uint256).maxKeep
StopLoss15% drawdown, 15%/day decay, unlockedAttached, 15% drawdown or less, 15%/day decay or less, timelock 1099511627775Change
Widest bin1% or less1% or lessKeep
Withdrawal extensionsNoneNoneKeep
CuratorVerifiedCreator is the admin and is verified by MetricKeep

Open the planner to try a configuration and get the StopLoss initialization payload.